![nissan data scan ii software nissan data scan ii software](https://img.informer.com/p7/nissan-datascan-ii-v2.5-main-window-display.png)
- #NISSAN DATA SCAN II SOFTWARE FOR FREE#
- #NISSAN DATA SCAN II SOFTWARE MANUAL#
- #NISSAN DATA SCAN II SOFTWARE PRO#
- #NISSAN DATA SCAN II SOFTWARE SOFTWARE#
- #NISSAN DATA SCAN II SOFTWARE PC#
Injector opening time is calculated by the ECU based on an engine load. O2 Sensors B1 and B2 are used on OBDII complaint cars and is located after the catalytic converter.ĭuty Cycle - is calculated from Injector time. This is a narrow band sensor and should never be used for tuning. ECU will switch to open mode while accelerating hard. This is normal and desirable for fuel economy. O2 Sensor - oscillates between 10 to 90 when engine is running in closed loop. Parameters are assigned to gauges in the Data Display Setup window. Readings from the wide band controller can be incorporated with the data logs for the ultimate performance and tuning data logging.ĭata Display window uses 12 gauges and 12 registers to display a real time information about the running engine as measured or calculated by the ECU.
#NISSAN DATA SCAN II SOFTWARE PRO#
Aftermarket ECUs like Apexi Power FC or F-Con V Pro are not compatible with this software.Ī support for a wide band sensors from TechEdge and Innovate Motorsports has also been added in the latest releases.
#NISSAN DATA SCAN II SOFTWARE SOFTWARE#
The Nissan DataScan I software supports factory Nissan engine ECUs. If you are able to connect to your car's ECU the Nissan DataScan I software will work on your car.
#NISSAN DATA SCAN II SOFTWARE FOR FREE#
The Data Replay, Log Analyser and Trip Computer functions are also available for free use. The unregistered software is limited to monitoring 2 engine parameters via the Dashboard function. If you are unsure you can always download the Nissan DataScan I software and test the connection to your car before registering the software. NOTE: Some vehicles up to year 2004 use OBDII (K-Line) for communicating with the ECU, BUT still use the Consult I (14pin) port for diagnostics. If your car is not on the list but has the above mentioned connector chances are the software will work just fine. The list is by no means comprehensive and is constantly being updated as new vehicles are tested. The connector is usually located near the fuse box.Ī list of cars that the software has been tested on is located on the Supported Vehicles page. Majority of these cars are equipped with grey 14 pin Consult I connector. Please test the unregistered version of the software before purchasing.The Nissan DataScan I is intended for Nissan cars build between years 19.
#NISSAN DATA SCAN II SOFTWARE PC#
#NISSAN DATA SCAN II SOFTWARE MANUAL#
Net Framework Version 3.5 SP1: dotnetfx35setup.zip - requires connection to internet to complete installation.ĭownload NDSII User Manual: NDSII User Manual Rev 1.pdf
![nissan data scan ii software nissan data scan ii software](https://nisscan.com/NDSII/pictures/ndsiiactwindow.jpg)
Note: Some vehicles may use K line for diagnostics of engine ECU (ECM) but still use DDL1 line for diagnostics of other control modules. The latest software release supports diagnostics of following control modules: ECM, BCM, TCM, ABS, SRS and ECMD (ECM Diesel) over the K line (DDL2).
![nissan data scan ii software nissan data scan ii software](https://cdn11.bigcommerce.com/s-0dvqh/images/stencil/1280x1280/products/638/5625/VAGCOM_FTDI_wm_1__69089.1458325788.jpg)
Aftermarket ECUs like Apexi Power FC or F-Con V Pro are not compatible with the software. The Nissan DataScan II software supports factory Nissan ECUs. The ELM327 chip based adapters are NOT compatible.Ĭompatible OS: Windows XP 7 8 8.1 10 (32/64bit) The software can be used with our FTDI FT232RL based OBD Innovations® OBDII KKL Adapter Cable. Some vehicles up to year 2004 use OBDII (K-Line) for communicating with the ECU, BUT still use the Consult I (14pin) port for diagnostics. NOTE: NOT COMPATIBLE with 2008+ cars that use the CAN BUS protocol. The Nissan DataScan II for Windows is intended for newer Nissan cars equipped with gray 16 pin OBDII connecter and use Consult II protocol over K line (DDL2) up to year 2007.